Aluminium has become a go-to material for home extensions, bi-fold doors, garden rooms and slim-framed windows. It’s strong, thin and doesn’t rot, which explains the popularity. What gets talked about far less is the finish, and that’s the bit that decides whether a frame still looks sharp in fifteen years.
Why the finish matters more than the metal
Aluminium itself is tough. The trouble starts at the surface. Any frame on the south or west side of a house takes a daily battering from sun, rain and temperature swings, and the finish is the only thing standing between the metal and the elements. A poor one fades, stains or lifts, and redoing a finish on installed frames is a far bigger job than choosing well at the start.
Location plays a big part. A frame in a sheltered garden has an easy life compared with one on a seafront terrace, where salt settles on the surface and wind-driven rain gets into every joint. Cut edges, drilled holes and fixings are the usual weak spots, because that’s where a surface layer is most likely to be disturbed.
Coatings versus treated metal
There are two broad routes. The first is a sprayed coating, usually powder coat, which is a layer of paint-like material baked onto the surface. It comes in a vast range of colours and it’s very common on domestic windows and doors. The second is a treatment that changes the metal’s own surface rather than adding something on top.
That second route is anodising aluminium. The metal goes into an electrolytic bath, where an electric current thickens the natural oxide layer into a hard, dense skin. Since the skin is part of the aluminium rather than a film sitting on top of it, there’s nothing to peel away, and the metal keeps a genuine metallic look instead of the flat, painted one. It’s more often seen on commercial buildings, though it can turn up on domestic cladding, door furniture and feature frames.
What a natural finish looks like
The clear, natural version leaves the aluminium its own silvery colour, and it can be matte or textured. That suits modern extensions with a lot of glass, where a restrained frame lets the view do the talking. It isn’t the right call for anyone after deep green or bright white, because natural finishing isn’t about colour. It’s about letting the metal look like metal.
In the UK, natural anodised work for buildings is normally made to BS 3987, the British Standard for external architectural anodising. A supplier that can confirm compliance is giving a useful signal about quality.
Natural finishes also work well alongside other materials. Pale timber cladding, red brick and render all sit comfortably next to soft silvery metal, and the tone is neutral enough to avoid clashing with whatever’s planted outside. That makes it a forgiving choice for anyone who isn’t sure how the garden or the exterior will look in five years.
Questions worth asking before ordering
Homeowners spending serious money on aluminium tend to get glossy brochures and very little detail about the finish. A few plain questions help.
- What’s the finish, and which standard does it meet?
- Is the colour guaranteed against fading, and for how long?
- How should it be cleaned, and how often?
- What happens at cut edges, such as where a frame’s been trimmed on site?
- Does the guarantee cover the finish as well as the frame?
Looking after aluminium once it’s in
Maintenance is mercifully light. A wash with warm water and a mild, non-abrasive cleaner a couple of times a year clears most grime. Abrasive pads and harsh solvents are best avoided because they can dull the surface. Homes near the sea may want a rinse more often, since salt deposits sit on metal and are better washed off.
Hinges, handles and seals are a separate matter and deserve an occasional check. A worn seal lets in more draught than a slightly faded frame ever will.
Budget and the long run
The cheapest quote and the cheapest frame over thirty years are rarely the same thing. Natural anodising is generally the least expensive of the anodic finishes, so it sits at the accessible end of the metal-finish options, but it’s still worth comparing against the cost of recoating or replacing a finish down the line. Spread across decades, the sums can look very different.
Recyclability is a quiet bonus. Aluminium can be melted down and reused many times over, and a clear anodic layer doesn’t add pigments or coatings that need stripping first.
Installers matter as much as the product. Even a very good finish can be damaged by rough handling on site, and scratches or dents at the point of fitting are much harder to deal with once the frames are in. It’s reasonable to ask how frames will be delivered, protected and signed off before the builders leave.
Choose the finish with the same care as the frame. Look at the standard it meets, ask about fading and cleaning, and compare costs over the life of the building rather than the first invoice. A frame that looks the same in 2040 as it did on the day it went in is worth a little extra thought now.